XCAM Max User Manual

  1. Thanks for choosing the XCAM Max
  2. What's in the box & your camera
  3. Buttons, lights & charging
  4. Install the app & create an account
  5. Connect with QR code (recommended)
  6. QR code setup: choose your WiFi
  7. QR code setup: camera scans your phone
  8. QR code setup: name & signal test
  9. Connect with Bluetooth
  10. Connect with the camera's hotspot
  11. Connect to or change WiFi
  12. Motion alerts
  13. Recording, storage & night vision
  14. Mounting, sharing & listening
  15. Troubleshooting
  16. Specifications, care & safety

Welcome

Thanks for choosing the XCAM Max

This guide takes you from unboxing to watching live on your phone, then covers motion alerts, recording, sharing and the settings you are most likely to need.

Contents

  • 1  What's in the box & your camera3
  • 2  Buttons, lights & charging4
  • 3  Install the app & create an account5
  • 4  Connect with QR code (recommended)6
  • 5  QR code setup: choose your WiFi7
  • 6  QR code setup: camera scans your phone8
  • 7  QR code setup: name & signal test9
  • 8  Connect with Bluetooth10
  • 9  Connect with the camera's hotspot11
  • 10  Connect to or change WiFi12
  • 11  Motion alerts13
  • 12  Recording, storage & night vision14
  • 13  Mounting, sharing & listening15
  • 14  Troubleshooting16
  • 15  Specifications, care & safety17

Before you start, you'll need

  • A smartphone (iPhone or Android).
  • A 2.4GHz WiFi network and its password. 5GHz, hidden and enterprise (work login) networks are not supported.
  • Optional: a microSD card up to 128GB so the camera can record by itself. Cards are sold separately.
  • An email address to create a free O-KAM Pro account.

Charge it first. Plug the camera into a 5V USB charger before first use. A full charge takes about 1 hour. The yellow light goes out when the battery is full.

Section 1

What's in the box & your camera

In the box

XCAM Max camera
Mounting bracket
Screw set
USB-C charging cable

Your camera

On its bracket

Back panel

  • 1Lens: 1080P, 130° wide angle
  • 2Infrared night vision, switches automatically
  • 3Power button on the back panel
  • 4USB-C charging port
  • 5microSD card slot (up to 128GB)
  • 6Reset button (R)
  • 7Indicator lights (blue, red, yellow)
  • 8Microphone

Section 2

Buttons, lights & charging

Power and reset

To… Do this
Switch on / off Press and hold the power button (on the back panel) for about 4 seconds.
Factory reset With the camera switched on, press and hold the reset button (R) for about 5 seconds, until the blue and red lights flash alternately. The camera restarts ready to be set up again.

What the lights mean

Light Meaning
Blue flashing slowly Waiting to be connected to WiFi.
Blue flashing quickly Connecting to WiFi.
Blue on Connected.
Blue and red flashing in turn Factory reset in progress.
Blue and red flashing together Low battery. Charge the camera.
Yellow on Charging. It goes out when the battery is full.

Charging

  • Use the USB-C cable supplied and a standard 5V / 1A USB charger. Do not use a charger that outputs more than 5V.
  • The 1600mAh battery gives about 8 hours of continuous recording. A full charge takes about 1 hour.
  • The camera keeps working while it charges, so you can leave it on USB power permanently.
  • It is normal for the camera to feel warm while it is running.

Section 3

Install the app & create an account

Install O-KAM Pro

  • Search for O-KAM Pro in the App Store (iPhone) or Google Play (Android), or scan the QR code on the leaflet in the box.

Create your account

  1. Open O-KAM Pro and tap Register now.
  2. Follow the prompts to register with your email, and agree to the user agreement and privacy policy.
  3. Log in. Allow notifications, so motion alerts can reach you.
Please login
Account
Password
Register now
Login

Register a free account

Get ready to connect

  • Switch the camera on: press and hold the power button (on the back panel) for about 4 seconds. A new camera is ready straight away: its blue light flashes. If the light isn't flashing, or the camera was set up before, reset it (Buttons, lights & charging).
  • Put the camera within 2 metres of your WiFi router for setup.
  • Connect your phone to your 2.4GHz WiFi and have the password ready.

There are three ways to connect the camera. Start with the QR code method (Connect with QR code (recommended)), which we have tested step by step. If it doesn't work for you, use Bluetooth (Connect with Bluetooth) or the camera's hotspot (Connect with the camera's hotspot).

Section 4

Connect with QR code (recommended)

The camera and the app swap QR codes: first your phone scans the label on the camera, then the camera scans a code on your phone. Have the camera switched on, with its blue light flashing (Install the app & create an account).

  1. Open O-KAM Pro and tap Add devices on the home screen.
  2. Scan the QR code label on the camera. This tells the app which camera you are adding.
  3. The app asks you to confirm the camera is ready. Check that the camera's blue light is flashing, tick I heard the prompt tone or see the indicator light flashing, and tap Next.

You won't hear a tone. This screen is the same for every O-KAM camera. The XCAM Max has a microphone but no speaker, so it makes no sound. Don't long-press the power button as the screen suggests: the camera is already on, and holding the button again would switch it off. The flashing blue light is all you need. If it isn't flashing, reset the camera (Buttons, lights & charging) and start again.

Home 🎧 ⊕
⊕
Add devices
Follow the steps to add the device to the app
HomeMessagesMine

Tap Add devices

← ✕
Confirm that the device is ready for network configuration

Check: is the device indicator flashing? Otherwise please reset the device first.

Battery device

Long press the power button until you hear the prompt tone from the device

☑I heard the prompt tone or see the indicator light flashing
Next

Blue light flashing? Tick the box, then Next

Section 5

QR code setup: choose your WiFi

  1. The app shows Searching for devices nearby. Keep the camera switched on and wait.
  2. On the Connect Wi-Fi screen, the app fills in the network your phone is on. Check it is your 2.4GHz network. If not, tap Switch network and choose it. Enter the WiFi password (tap the eye to check it), then tap Next.

Use the 2.4GHz network. The camera can't join a 5GHz, hidden or enterprise (work login) network. If your router shows one name for both bands and setup fails, ask your internet provider how to give 2.4GHz its own name. Leave Remember Wi-Fi name and password ticked to save typing next time.

←
Searching for devices nearby

Please keep the device powered on

Keep the camera on and wait

←  Connect Wi-Fi

Please select 2.4GHz Wi-Fi and enter the password… Hidden Wi-Fi can't support the network connection

📶 Home-WiFiSwitch network
🔒 ••••••••••👁
● Remember Wi-Fi name and password
Next

Check it's 2.4GHz, enter the password

Section 6

QR code setup: camera scans your phone

  1. The app shows a QR code made just for this setup. Hold your phone 15 to 30 cm in front of the camera lens, with the screen facing the lens. Move it slowly closer or further away until the camera reads the code. The app moves on by itself as soon as it does.
  2. Wait while the camera connects, which takes 1 to 2 minutes: Camera accesses network → Registering Cloud Services → Camera adds to App. Keep your phone on the same WiFi and leave the app open.

Camera won't read the code? Turn your phone's screen brightness up, tilt the phone a little to get rid of reflections, and hold it still for a few seconds at each distance. The screen shows a countdown. If it runs out, go back and try again.

←  Scan the QR code
15–30 cm

After the connection is successful, it will automatically jump to the next step.

88s

Example only. Your app makes its own code each time

←  VE1234567ABCD
Connecting…

The connection process takes about 1–2 minutes, please do not disconnect the network

✔ Camera accesses network
◌ Registering Cloud Services
● Camera adds to App

Wait 1 to 2 minutes

Section 7

QR code setup: name & signal test

  1. The app asks you to confirm binding the camera. The screen shows your camera's ID (every camera has its own). Type a name or tap a suggestion such as Office or Living room, then tap Next.
  2. The app tests the WiFi signal where the camera is and shows its live picture. If the signal is Strong, tap Done. If it is weak, move the camera closer to your router and tap Retry.
Confirm binding Camera “VE1234567ABCD”

Camera name

Office⊗

Common name

Garage
Front door
Yard
Living room
Office
Bedroom
Next

Example ID. Your camera's ID is different

←  Check the WiFi signal
live picture
Testing completed
The WiFi signal at the current location is suitable for installing the device.
Wi-Fi signal: Strong
Retry
Done

Strong signal? Tap Done

The camera now appears on the O-KAM Pro home screen, and its blue light stays on. Tap the camera to watch live.

The app may offer a free cloud-storage trial during setup. It is optional: tap past it if you only want to record to the microSD card.

Section 8

Connect with Bluetooth

  1. Turn on your phone's Bluetooth (and location, if your phone asks).
  2. Open O-KAM Pro. After a moment the camera appears at the top of the home screen as a new device. Tap Connect. If it doesn't appear, tap + Add to search again, or scan the QR code on the camera.
  3. Confirm your 2.4GHz WiFi network, enter the password and tap Next.
  4. Wait while the camera connects, which takes 1 to 2 minutes: Camera accesses network → Camera found → Camera adds to App.
  5. Give the camera a name (for example Living room) and tap Get started.
  6. Choose whether to turn on Notification push and Motion Detection (Motion alerts), then tap Get started.
Homepage ⊕
IPC-…Discovering a new device, click to connect
Connect
Add a new device+ Add

Tap Connect on the new device

The app offers a free cloud-storage trial during setup. It is optional: tap past it if you only want to record to the microSD card.

Section 9

Connect with the camera's hotspot

  1. Switch the camera on and reset it to factory settings.
  2. In O-KAM Pro, tap ⊕ in the top right and choose Hotspot configuration.
  3. Tap To connect.
  4. In your phone's WiFi settings, join the camera's network. Its name starts with @MC- (it may also start with @OK-, @IPC-, @YX-, @LaiCam- or IPC-).
  5. Go back to O-KAM Pro. The camera is added automatically. Tap the play button to watch.
← WLAN
@MC-123456Connected◔
Home-WiFiSaved◔
Neighbour-5GSecured◔

Join the @MC-… network

A camera added this way shows AP on its card and can only be watched while your phone is joined to the camera's network. To watch from anywhere, connect it to your home WiFi (Connect to or change WiFi).

Section 10

Connect to or change WiFi

Use this to move a hotspot-connected camera onto your home WiFi, or after you change your router or WiFi password.

  1. On the home screen, tap ⋮ on the camera's card, then Settings.
  2. Tap Device Settings.
  3. Tap Wi-Fi network.
  4. Choose your 2.4GHz network, enter the password and tap Confirm. The camera reconnects, and the blue light stays on when it's done.
← System settings
Device Settings
Power mode
Device Health
Monitoring Function
AI Smart Service
TF Record Settings
Help center
Notification Settings

System settings. Your app version may differ slightly.

Other device settings

Setting What it does
Device name Rename the camera.
Device volume Microphone level.
Hide indicator light Turn the camera's lights off.
Make it priority view camera Show this camera first on the home screen.
Video management Video settings for this camera.
Enhanced WiFi mode Helps where the signal is weak.
Restart device Reboot the camera.

Section 11

Motion alerts

The XCAM Max detects changes in the picture. It does not tell people apart from pets, and moving curtains, shadows, sunlight or headlights can also set it off.

  • Reposition first. Keep windows, TVs, plants and pet routes out of the frame.
  • If there is a lot of normal movement where the camera is, you can switch motion detection off and use it as a live-view camera.
  • Every alert uses battery. For an alert camera, keep it on USB power.

Turn alerts on or off

  • During setup, the camera's settings page offers Notification push and Motion Detection switches.
  • Later, open the camera's ⚙ Settings and use Notification Settings and Monitoring Function.
  • Allow notifications for O-KAM Pro in your phone's settings, or the alerts won't appear.
  • Tap the bell (Silence) on the camera's card to pause alerts for a while.

See what happened

Tap an alert to open the camera. Past recordings are under Playback on the camera's card and in Messages.

Section 12

Recording, storage & night vision

microSD card

  • Supports cards up to 128GB. Cards are sold separately.
  • Insert the card into the camera's card slot with the camera switched off.
  • Choose how the camera records to the card in ⚙ Settings → TF Record Settings.
  • Watch recordings with Playback on the camera's card.
  • If the camera doesn't recognise the card, format it from TF Record Settings or try a different card.

Cloud storage (optional)

O-KAM Pro offers paid cloud storage, and the app may show a free trial and upgrade prompts. You don't need it: the camera records to the microSD card with no subscription.

Stop any recording before you switch the camera off, or the last video file may not be saved.

Night vision

Night vision switches on automatically when the room goes dark, and back to colour when the light returns.

Section 13

Mounting, sharing & listening

Mounting

Fix the camera to its bracket. The bracket can stand on a shelf, or be screwed to a wall with the supplied screw set. Loosen the knob to set the angle, then tighten it.

Share with family

  1. On the home screen, tap ⋮ on the camera's card, then Share. A QR code appears.
  2. Choose whether to Offer setting permissions.
  3. The other person installs O-KAM Pro, logs in and scans the code. Each code is valid for 30 minutes and can be used by one person.

Up to 4 people can watch the camera at the same time.

Listening

The camera has a built-in microphone, so you can hear the room in the live view. It has no speaker, so you can't talk through it.

Section 14

Troubleshooting

Problem Try this
App can't find the camera Check the blue light is flashing (if not, reset the camera), keep it within 2 metres of the router, and make sure your phone is on 2.4GHz WiFi. Then try QR code setup again (Connect with QR code (recommended)), or use Bluetooth (Connect with Bluetooth).
Camera won't read the code on your phone Hold the phone 15 to 30 cm from the lens, screen brightness up, no reflections. If the countdown runs out, go back and try again (QR code setup: camera scans your phone).
App asks about a prompt tone The XCAM Max has no speaker, so there is no tone. Go by the flashing blue light and tick the box (Connect with QR code (recommended)).
Weak signal in the WiFi test Move the camera closer to the router, or move the router, then tap Retry (QR code setup: name & signal test).
Can't see the @MC-… network Reset the camera and wait for the blue light to flash slowly, then refresh your phone's WiFi list.
Won't join home WiFi Use a 2.4GHz network (not 5GHz, hidden or enterprise) and check the password. Try Enhanced WiFi mode where the signal is weak.
Changed router or WiFi password Change it in Device Settings → Wi-Fi network (Connect to or change WiFi), or reset the camera and set it up again.
Only works near the camera It is in hotspot (AP) mode. Connect it to your home WiFi (Connect to or change WiFi).
No motion alerts Check Motion Detection and Notification push are on, Silence is off, and notifications are allowed for O-KAM Pro on your phone.
Too many alerts Reposition the camera away from windows, TVs and pets (Motion alerts).
Blue and red flash together Low battery. Charge the camera.
microSD card not recognised Format it in TF Record Settings, or try another card of 128GB or less.
Asked to pay for cloud storage Optional. Recording to the microSD card is free.
Camera feels warm Normal during use. It does not affect performance.

Section 15

Specifications, care & safety

Model Lexuma XCAM Max (W11)
Video 1080P Full HD, 15fps
Lens 130° diagonal
Night vision Infrared, switches automatically
Motion detection Picture-change detection with app alerts
Audio Built-in microphone (listen only)
Storage microSD up to 128GB (not included); optional paid cloud storage
WiFi 2.4GHz (WiFi 6) + Bluetooth for setup
Battery 1600mAh built-in, about 8 hours continuous, low-battery alert
Charging USB-C, 5V / 1A, about 1 hour
Power 0.9W
Size / weight 42 × 42 × 41 mm / 56.2g
Operating −10°C to +55°C, humidity below 90%
App O-KAM Pro (iOS & Android)

Care & safety

  • Charge only with a 5V USB charger. Don't use damaged cables, and don't use a charger that outputs more than 5V.
  • For indoor use. Keep the camera away from water, rain, high humidity and direct heat.
  • Don't open the camera or try to replace the built-in battery.
  • Keep small parts away from young children.
  • Recycle the camera and its battery responsibly. Don't put them in household waste.

Using a camera responsibly

Monitoring your own home, property or business is legal in most countries. Recording people where they reasonably expect privacy is not, and audio recording carries extra restrictions in many places. Check the rules where you live before you place the camera, and tell guests, tenants or staff where cameras are in use.

Questions? Email shop@lexuma.com.